TURNING POINT PROPELLERS 2150 1740 PROP HUSTLER 4BL AL 14.5X17 LH
Price: $161.89
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers 21501740 Hustler Propeller 14.5x17, 4-Blade Aluminum, LH Rotation
These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
This Dual Geometry propeller is uniquely engineered with two blade geometries: two blades utilize the Hustler high performance variable rake and aggressive pitch design for incredible hole shot and cornering, and two blades utilize an offshore style design for high speed and maximum stern lift. These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
Lifts the entire boat higher out of the water:
By lifting the hull higher, boats tend to lose less speed when fully loaded versus a 3-Blade prop. With a lightly loaded boat, a 3-Blade is usually the faster prop for most applications. Alternatively when an application is loaded down with extra people and gear, a 3-Bladed prop can lose up to 3 MPH. This is because the hull is forced deeper into the water causing more wetted surface by the added weight. By lifting the hull higher the Turning Point 4 blade when fully loaded does not lose the top end speed compared to a 3-Blade propeller.
The Huslter 4 blade series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older aluminum designs from the 70's, 80's, 90's, and '00's, and will outrun most newer props, including five blade ski props.
Squeeze Cast for Added Strength:
Stainless steel performance is built into the Hustler Aluminum prop line. This is achieved through unique blade geometry and an exclusive Turning Point manufacturing process, Squeeze Casting. This process generates the highest mechanical properties attainable in a cast aluminum prop resulting from high density tighter grain structure. Stiffer blades means less flex and a faster prop. Competitors' Aluminum propellers are manufactured utilizing old Die-Cast process that produces props with air bubble, voids, and granularity. Weak, lack of strength and stiffness. Difficult to repair. Blades Flex under load, inefficient, loss of propulsive efficiency.
Long Lasting Ultracoat™ Powder Coated Finish:
Exclusive to Turning Point, the Ultracoat powder coat rivals a fine automotive finish, and is more durable than paint. Utilizing a state-of-the-art five step process, Ultracoat gives the propeller a shiny, uniform appearance that enhances any boat's good looks. This is the Gold Standard in Aluminum Corrosion Protection. Prop looks Newer Longer! Compared to Competitors' 4 step Paint and Coating Processes that result in much less abrasion and corrosion resistance.
Large Free Flowing Exhaust Ports:
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
- Hustler® Aluminum Dual Geometry 4 Blade Props for 90-300+hp Engines with 4.75" Gearcases.
- 4 Blades That Re-wrote the Rules.
- The props that put the "four" in Perfourmance!
- Unprecedented hole shot, lift, handling, ease of steering, and rough water stability.
- No top-end speed loss you experience with other manufacturers' 4 blade propellers keeps 3 blade top end speed.
- Lifts the entire boat higher out of the water.
- 4 blade Dual Geometry prop that has 3 blade top end speed with fast hole shot and unmatched handling.
- Stainless steel performance at aluminum prices with tuned exhaust vents improve hole shot.
- Squeeze casting adds strength that boosts performance with protected by five-step powder-coated finish.
- Propellers fit COX®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, MerCruiser®, Nissan®, OMC®, OXE®, Parsun®, Suzuki®, Tohatsu®,Volvo Penta®, & Yamaha® Outboards and Sterndrives.
- Uses 500 series Installation/hub kits only-Sold separately.
- See application chart for engine application information and required Installation/hub kit part numbers.
These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
This Dual Geometry propeller is uniquely engineered with two blade geometries: two blades utilize the Hustler high performance variable rake and aggressive pitch design for incredible hole shot and cornering, and two blades utilize an offshore style design for high speed and maximum stern lift. These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
Lifts the entire boat higher out of the water:
By lifting the hull higher, boats tend to lose less speed when fully loaded versus a 3-Blade prop. With a lightly loaded boat, a 3-Blade is usually the faster prop for most applications. Alternatively when an application is loaded down with extra people and gear, a 3-Bladed prop can lose up to 3 MPH. This is because the hull is forced deeper into the water causing more wetted surface by the added weight. By lifting the hull higher the Turning Point 4 blade when fully loaded does not lose the top end speed compared to a 3-Blade propeller.
The Huslter 4 blade series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older aluminum designs from the 70's, 80's, 90's, and '00's, and will outrun most newer props, including five blade ski props.
Squeeze Cast for Added Strength:
Stainless steel performance is built into the Hustler Aluminum prop line. This is achieved through unique blade geometry and an exclusive Turning Point manufacturing process, Squeeze Casting. This process generates the highest mechanical properties attainable in a cast aluminum prop resulting from high density tighter grain structure. Stiffer blades means less flex and a faster prop. Competitors' Aluminum propellers are manufactured utilizing old Die-Cast process that produces props with air bubble, voids, and granularity. Weak, lack of strength and stiffness. Difficult to repair. Blades Flex under load, inefficient, loss of propulsive efficiency.
Long Lasting Ultracoat™ Powder Coated Finish:
Exclusive to Turning Point, the Ultracoat powder coat rivals a fine automotive finish, and is more durable than paint. Utilizing a state-of-the-art five step process, Ultracoat gives the propeller a shiny, uniform appearance that enhances any boat's good looks. This is the Gold Standard in Aluminum Corrosion Protection. Prop looks Newer Longer! Compared to Competitors' 4 step Paint and Coating Processes that result in much less abrasion and corrosion resistance.
Large Free Flowing Exhaust Ports:
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
ALT Part Numbers: TUR 21501740, 25-4553
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-21501740
UPC:652480102486
TURNING POINT PROPELLERS 21501930 PROP HUSTLER 4BL AL 14X19 RH
Price: $134.99
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers 21501930 Hustler Propeller 14x19, 4-Blade Aluminum, RH Rotation (Standard)
These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
This Dual Geometry propeller is uniquely engineered with two blade geometries: two blades utilize the Hustler high performance variable rake and aggressive pitch design for incredible hole shot and cornering, and two blades utilize an offshore style design for high speed and maximum stern lift. These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
Lifts the entire boat higher out of the water:
By lifting the hull higher, boats tend to lose less speed when fully loaded versus a 3-Blade prop. With a lightly loaded boat, a 3-Blade is usually the faster prop for most applications. Alternatively when an application is loaded down with extra people and gear, a 3-Bladed prop can lose up to 3 MPH. This is because the hull is forced deeper into the water causing more wetted surface by the added weight. By lifting the hull higher the Turning Point 4 blade when fully loaded does not lose the top end speed compared to a 3-Blade propeller.
The Huslter 4 blade series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older aluminum designs from the 70's, 80's, 90's, and '00's, and will outrun most newer props, including five blade ski props.
Squeeze Cast for Added Strength:
Stainless steel performance is built into the Hustler Aluminum prop line. This is achieved through unique blade geometry and an exclusive Turning Point manufacturing process, Squeeze Casting. This process generates the highest mechanical properties attainable in a cast aluminum prop resulting from high density tighter grain structure. Stiffer blades means less flex and a faster prop. Competitors' Aluminum propellers are manufactured utilizing old Die-Cast process that produces props with air bubble, voids, and granularity. Weak, lack of strength and stiffness. Difficult to repair. Blades Flex under load, inefficient, loss of propulsive efficiency.
Long Lasting Ultracoat™ Powder Coated Finish:
Exclusive to Turning Point, the Ultracoat powder coat rivals a fine automotive finish, and is more durable than paint. Utilizing a state-of-the-art five step process, Ultracoat gives the propeller a shiny, uniform appearance that enhances any boat's good looks. This is the Gold Standard in Aluminum Corrosion Protection. Prop looks Newer Longer! Compared to Competitors' 4 step Paint and Coating Processes that result in much less abrasion and corrosion resistance.
Large Free Flowing Exhaust Ports:
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
- Hustler® Aluminum Dual Geometry 4 Blade Props for 90-300+hp Engines with 4.75" Gearcases.
- 4 Blades That Re-wrote the Rules.
- The props that put the "four" in Perfourmance!
- Unprecedented hole shot, lift, handling, ease of steering, and rough water stability.
- No top-end speed loss you experience with other manufacturers' 4 blade propellers keeps 3 blade top end speed.
- Lifts the entire boat higher out of the water.
- 4 blade Dual Geometry prop that has 3 blade top end speed with fast hole shot and unmatched handling.
- Stainless steel performance at aluminum prices with tuned exhaust vents improve hole shot.
- Squeeze casting adds strength that boosts performance with protected by five-step powder-coated finish.
- Propellers fit COX®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, MerCruiser®, Nissan®, OMC®, OXE®, Parsun®, Suzuki®, Tohatsu®,Volvo Penta®, & Yamaha® Outboards and Sterndrives.
- Uses 500 series Installation/hub kits only-Sold separately.
- See application chart for engine application information and required Installation/hub kit part numbers.
These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
This Dual Geometry propeller is uniquely engineered with two blade geometries: two blades utilize the Hustler high performance variable rake and aggressive pitch design for incredible hole shot and cornering, and two blades utilize an offshore style design for high speed and maximum stern lift. These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
Lifts the entire boat higher out of the water:
By lifting the hull higher, boats tend to lose less speed when fully loaded versus a 3-Blade prop. With a lightly loaded boat, a 3-Blade is usually the faster prop for most applications. Alternatively when an application is loaded down with extra people and gear, a 3-Bladed prop can lose up to 3 MPH. This is because the hull is forced deeper into the water causing more wetted surface by the added weight. By lifting the hull higher the Turning Point 4 blade when fully loaded does not lose the top end speed compared to a 3-Blade propeller.
The Huslter 4 blade series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older aluminum designs from the 70's, 80's, 90's, and '00's, and will outrun most newer props, including five blade ski props.
Squeeze Cast for Added Strength:
Stainless steel performance is built into the Hustler Aluminum prop line. This is achieved through unique blade geometry and an exclusive Turning Point manufacturing process, Squeeze Casting. This process generates the highest mechanical properties attainable in a cast aluminum prop resulting from high density tighter grain structure. Stiffer blades means less flex and a faster prop. Competitors' Aluminum propellers are manufactured utilizing old Die-Cast process that produces props with air bubble, voids, and granularity. Weak, lack of strength and stiffness. Difficult to repair. Blades Flex under load, inefficient, loss of propulsive efficiency.
Long Lasting Ultracoat™ Powder Coated Finish:
Exclusive to Turning Point, the Ultracoat powder coat rivals a fine automotive finish, and is more durable than paint. Utilizing a state-of-the-art five step process, Ultracoat gives the propeller a shiny, uniform appearance that enhances any boat's good looks. This is the Gold Standard in Aluminum Corrosion Protection. Prop looks Newer Longer! Compared to Competitors' 4 step Paint and Coating Processes that result in much less abrasion and corrosion resistance.
Large Free Flowing Exhaust Ports:
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
ALT Part Numbers: TUR 21501930, 24-0796
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-21501930
UPC:652480102462
TURNING POINT PROPELLERS 2150 1940 PROP HUSTLER 4BL AL 14X19 LH
Price: $161.89
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers 21501940 Hustler Propeller 14x19, 4-Blade Aluminum, LH Rotation
These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
This Dual Geometry propeller is uniquely engineered with two blade geometries: two blades utilize the Hustler high performance variable rake and aggressive pitch design for incredible hole shot and cornering, and two blades utilize an offshore style design for high speed and maximum stern lift. These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
Lifts the entire boat higher out of the water:
By lifting the hull higher, boats tend to lose less speed when fully loaded versus a 3-Blade prop. With a lightly loaded boat, a 3-Blade is usually the faster prop for most applications. Alternatively when an application is loaded down with extra people and gear, a 3-Bladed prop can lose up to 3 MPH. This is because the hull is forced deeper into the water causing more wetted surface by the added weight. By lifting the hull higher the Turning Point 4 blade when fully loaded does not lose the top end speed compared to a 3-Blade propeller.
The Huslter 4 blade series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older aluminum designs from the 70's, 80's, 90's, and '00's, and will outrun most newer props, including five blade ski props.
Squeeze Cast for Added Strength:
Stainless steel performance is built into the Hustler Aluminum prop line. This is achieved through unique blade geometry and an exclusive Turning Point manufacturing process, Squeeze Casting. This process generates the highest mechanical properties attainable in a cast aluminum prop resulting from high density tighter grain structure. Stiffer blades means less flex and a faster prop. Competitors' Aluminum propellers are manufactured utilizing old Die-Cast process that produces props with air bubble, voids, and granularity. Weak, lack of strength and stiffness. Difficult to repair. Blades Flex under load, inefficient, loss of propulsive efficiency.
Long Lasting Ultracoat™ Powder Coated Finish:
Exclusive to Turning Point, the Ultracoat powder coat rivals a fine automotive finish, and is more durable than paint. Utilizing a state-of-the-art five step process, Ultracoat gives the propeller a shiny, uniform appearance that enhances any boat's good looks. This is the Gold Standard in Aluminum Corrosion Protection. Prop looks Newer Longer! Compared to Competitors' 4 step Paint and Coating Processes that result in much less abrasion and corrosion resistance.
Large Free Flowing Exhaust Ports:
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
- Hustler® Aluminum Dual Geometry 4 Blade Props for 90-300+hp Engines with 4.75" Gearcases.
- 4 Blades That Re-wrote the Rules.
- The props that put the "four" in Perfourmance!
- Unprecedented hole shot, lift, handling, ease of steering, and rough water stability.
- No top-end speed loss you experience with other manufacturers' 4 blade propellers keeps 3 blade top end speed.
- Lifts the entire boat higher out of the water.
- 4 blade Dual Geometry prop that has 3 blade top end speed with fast hole shot and unmatched handling.
- Stainless steel performance at aluminum prices with tuned exhaust vents improve hole shot.
- Squeeze casting adds strength that boosts performance with protected by five-step powder-coated finish.
- Propellers fit COX®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, MerCruiser®, Nissan®, OMC®, OXE®, Parsun®, Suzuki®, Tohatsu®,Volvo Penta®, & Yamaha® Outboards and Sterndrives.
- Uses 500 series Installation/hub kits only-Sold separately.
- See application chart for engine application information and required Installation/hub kit part numbers.
These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
This Dual Geometry propeller is uniquely engineered with two blade geometries: two blades utilize the Hustler high performance variable rake and aggressive pitch design for incredible hole shot and cornering, and two blades utilize an offshore style design for high speed and maximum stern lift. These props re-wrote the rules, proving that you can run a 4-Blade that has unprecedented hole shot, handling, and rough water stability without the top-end speed loss you experience with other manufacturers' propellers.
Lifts the entire boat higher out of the water:
By lifting the hull higher, boats tend to lose less speed when fully loaded versus a 3-Blade prop. With a lightly loaded boat, a 3-Blade is usually the faster prop for most applications. Alternatively when an application is loaded down with extra people and gear, a 3-Bladed prop can lose up to 3 MPH. This is because the hull is forced deeper into the water causing more wetted surface by the added weight. By lifting the hull higher the Turning Point 4 blade when fully loaded does not lose the top end speed compared to a 3-Blade propeller.
The Huslter 4 blade series is perfect for any application that demands enhanced acceleration, cornering, and load carrying capabilities. This prop series is ideally suited for watersports, sterndrive boats, tri-toons, bay boats, and any vessel that can use stern lift. It is our best upgrade of older aluminum designs from the 70's, 80's, 90's, and '00's, and will outrun most newer props, including five blade ski props.
Squeeze Cast for Added Strength:
Stainless steel performance is built into the Hustler Aluminum prop line. This is achieved through unique blade geometry and an exclusive Turning Point manufacturing process, Squeeze Casting. This process generates the highest mechanical properties attainable in a cast aluminum prop resulting from high density tighter grain structure. Stiffer blades means less flex and a faster prop. Competitors' Aluminum propellers are manufactured utilizing old Die-Cast process that produces props with air bubble, voids, and granularity. Weak, lack of strength and stiffness. Difficult to repair. Blades Flex under load, inefficient, loss of propulsive efficiency.
Long Lasting Ultracoat™ Powder Coated Finish:
Exclusive to Turning Point, the Ultracoat powder coat rivals a fine automotive finish, and is more durable than paint. Utilizing a state-of-the-art five step process, Ultracoat gives the propeller a shiny, uniform appearance that enhances any boat's good looks. This is the Gold Standard in Aluminum Corrosion Protection. Prop looks Newer Longer! Compared to Competitors' 4 step Paint and Coating Processes that result in much less abrasion and corrosion resistance.
Large Free Flowing Exhaust Ports:
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
ALT Part Numbers: TUR 21501940, 25-4554
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-21501940
UPC:652480102493
TURNING POINT PROPELLERS 11300200 HUB MASTRGRD RND 3.5"GC YM HON
Price: $44.99
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers MasterGuard Installation Kit 12 (11300200)
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
- MasterGuard 10 Series Installation Kit for Engines with 3.5" Gearcase
- MasterGuard Installation/Hub Kits carry the only Lifetime Warranty in the WORLD!
- Hubs have no warranty restrictions, except for extreme commercial use.
- Saves a boater up to 33% on replacement propeller purchases (need to purchase prop housing only).
- One piece design: durable marine Bronze with Over Molded Glass Filled Nylon for Long Life.
- Re-useable after a Prop Strike.
- Warranted even if the prop is Destroyed! (consumer normal use only, not applicable on commercial applications)
- Enhanced lower unit protection.
- Utilizes a specially designed keyway system and a hi-tech polymer designed to absorb shift shock and harmful vibrations.
- The small diameter design allows for more exhaust flow and higher horsepower.
- Adapts to the OEM thrust washer and prop nut.
- Included accessories and parts: Hub assembly, prop nut spacer, installation instructions.
- Installation Kits for Colman®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, Nissan®, Parsun®, Suzuki®, Tohatsu®, & Yamaha® Outboards.
- Use with Hustler or Express Mach3 propeller housings for 25-75hp engines with 3.5" gearcase.
- See application chart for engine application information.
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
ALT Part Numbers: TUR 11300200, 23-6411, 26-6710
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-11300200
UPC:652480200403
TURNING POINT PROPELLERS 11200100 HUB MASTERGUARD RND 3"GC MERC
Price: $43.79
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers MasterGuard Installation Kit 21 (11200100)
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
- MasterGuard® 20 Series Installation Kit for Engines with 3" Gearcase
- MasterGuard Installation/Hub Kits carry the only Lifetime Warranty in the WORLD!
- Hubs have no warranty restrictions, except for extreme commercial use.
- Saves a boater up to 33% on replacement propeller purchases (need to purchase prop housing only).
- One piece design: durable marine Bronze with Over Molded Glass Filled Nylon for Long Life.
- Re-useable after a Prop Strike.
- Warranted even if the prop is Destroyed! (consumer normal use only, not applicable on commercial applications)
- Enhanced lower unit protection.
- Utilizes a specially designed keyway system and a hi-tech polymer designed to absorb shift shock and harmful vibrations.
- The small diameter design allows for more exhaust flow and higher horsepower.
- Adapts to the OEM thrust washer and prop nut.
- Included accessories and parts: Hub assembly, prop nut spacer, installation instructions.
- Installation Kits for Colman®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, Nissan®, Parsun®, Suzuki®, Tohatsu®, & Yamaha® Outboards.
- Use with Hustler or Express Mach3 propeller housings for 9.9-35hp engines with 3" gearcase.
- See application chart for engine application information.
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
ALT Part Numbers: TUR 11200100, 23-6399, 26-6718
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-11200100
UPC:652480200151
TURNING POINT PROPELLERS 11200200 HUB MASTERGUARD RND 3"GC BRP
Price: $43.79
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers MasterGuard Installation Kit 22 (11200200)
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
- MasterGuard® 20 Series Installation Kit for Engines with 3" Gearcase
- MasterGuard Installation/Hub Kits carry the only Lifetime Warranty in the WORLD!
- Hubs have no warranty restrictions, except for extreme commercial use.
- Saves a boater up to 33% on replacement propeller purchases (need to purchase prop housing only).
- One piece design: durable marine Bronze with Over Molded Glass Filled Nylon for Long Life.
- Re-useable after a Prop Strike.
- Warranted even if the prop is Destroyed! (consumer normal use only, not applicable on commercial applications)
- Enhanced lower unit protection.
- Utilizes a specially designed keyway system and a hi-tech polymer designed to absorb shift shock and harmful vibrations.
- The small diameter design allows for more exhaust flow and higher horsepower.
- Adapts to the OEM thrust washer and prop nut.
- Included accessories and parts: Hub assembly, prop nut spacer, installation instructions.
- Installation Kits for Colman®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, Nissan®, Parsun®, Suzuki®, Tohatsu®, & Yamaha® Outboards.
- Use with Hustler or Express Mach3 propeller housings for 9.9-35hp engines with 3" gearcase.
- See application chart for engine application information.
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
ALT Part Numbers: TUR 11200200, 23-6400, 26-6719
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-11200200
UPC:652480200168
TURNING POINT PROPELLERS 11200500 HUB MASTERGUARD RND 3"GC YAM
Price: $43.79
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers MasterGuard Installation Kit 25 (11200500)
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
- MasterGuard® 20 Series Installation Kit for Engines with 3" Gearcase
- MasterGuard Installation/Hub Kits carry the only Lifetime Warranty in the WORLD!
- Hubs have no warranty restrictions, except for extreme commercial use.
- Saves a boater up to 33% on replacement propeller purchases (need to purchase prop housing only).
- One piece design: durable marine Bronze with Over Molded Glass Filled Nylon for Long Life.
- Re-useable after a Prop Strike.
- Warranted even if the prop is Destroyed! (consumer normal use only, not applicable on commercial applications)
- Enhanced lower unit protection.
- Utilizes a specially designed keyway system and a hi-tech polymer designed to absorb shift shock and harmful vibrations.
- The small diameter design allows for more exhaust flow and higher horsepower.
- Adapts to the OEM thrust washer and prop nut.
- Included accessories and parts: Hub assembly, prop nut spacer, installation instructions.
- Installation Kits for Colman®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, Nissan®, Parsun®, Suzuki®, Tohatsu®, & Yamaha® Outboards.
- Use with Hustler or Express Mach3 propeller housings for 9.9-35hp engines with 3" gearcase.
- See application chart for engine application information.
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
ALT Part Numbers: TUR 11200500, 23-6401, 26-6720
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-11200500
UPC:652480200175
TURNING POINT PROPELLERS 11200600 HUB MASTERGUARD RND 3"GC SUZ
Price: $43.79
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers MasterGuard Installation Kit 26 (11200600)
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
- MasterGuard® 20 Series Installation Kit for Engines with 3" Gearcase
- MasterGuard Installation/Hub Kits carry the only Lifetime Warranty in the WORLD!
- Hubs have no warranty restrictions, except for extreme commercial use.
- Saves a boater up to 33% on replacement propeller purchases (need to purchase prop housing only).
- One piece design: durable marine Bronze with Over Molded Glass Filled Nylon for Long Life.
- Re-useable after a Prop Strike.
- Warranted even if the prop is Destroyed! (consumer normal use only, not applicable on commercial applications)
- Enhanced lower unit protection.
- Utilizes a specially designed keyway system and a hi-tech polymer designed to absorb shift shock and harmful vibrations.
- The small diameter design allows for more exhaust flow and higher horsepower.
- Adapts to the OEM thrust washer and prop nut.
- Included accessories and parts: Hub assembly, prop nut spacer, installation instructions.
- Installation Kits for Colman®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, Nissan®, Parsun®, Suzuki®, Tohatsu®, & Yamaha® Outboards.
- Use with Hustler or Express Mach3 propeller housings for 9.9-35hp engines with 3" gearcase.
- See application chart for engine application information.
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
ALT Part Numbers: TUR 11200600, 23-6402, 26-6721
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-11200600
UPC:652480200182
TURNING POINT PROPELLERS 11200800 HUB MASTERGUARD RND 3"GC HON
Price: $43.79
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers MasterGuard Installation Kit 28 (11200800)
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
- MasterGuard® 20 Series Installation Kit for Engines with 3" Gearcase
- MasterGuard Installation/Hub Kits carry the only Lifetime Warranty in the WORLD!
- Hubs have no warranty restrictions, except for extreme commercial use.
- Saves a boater up to 33% on replacement propeller purchases (need to purchase prop housing only).
- One piece design: durable marine Bronze with Over Molded Glass Filled Nylon for Long Life.
- Re-useable after a Prop Strike.
- Warranted even if the prop is Destroyed! (consumer normal use only, not applicable on commercial applications)
- Enhanced lower unit protection.
- Utilizes a specially designed keyway system and a hi-tech polymer designed to absorb shift shock and harmful vibrations.
- The small diameter design allows for more exhaust flow and higher horsepower.
- Adapts to the OEM thrust washer and prop nut.
- Included accessories and parts: Hub assembly, prop nut spacer, installation instructions.
- Installation Kits for Colman®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, Nissan®, Parsun®, Suzuki®, Tohatsu®, & Yamaha® Outboards.
- Use with Hustler or Express Mach3 propeller housings for 9.9-35hp engines with 3" gearcase.
- See application chart for engine application information.
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
ALT Part Numbers: TUR 11200800, 23-6403, 26-6722
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-11200800
UPC:652480200199
TURNING POINT PROPELLERS 11100101 HUB MASTERGUARD RND 2.5"GC MER
Price: $33.49
Retail price is shown. * Add this item to the Shopping Cart to see your reduced price.
Product Description: Turning Point Propellers MasterGuard Installation Kit 201 (11100101)
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
- MasterGuard® 200 Series Installation Kit for Engines with 2.5" Gearcase
- MasterGuard Installation/Hub Kits carry the only Lifetime Warranty in the WORLD!
- Hubs have no warranty restrictions, except for extreme commercial use.
- Saves a boater up to 33% on replacement propeller purchases (need to purchase prop housing only).
- One piece design: durable marine Bronze with Over Molded Glass Filled Nylon for Long Life.
- Re-useable after a Prop Strike.
- Warranted even if the prop is Destroyed! (consumer normal use only, not applicable on commercial applications)
- Enhanced lower unit protection.
- Utilizes a specially designed keyway system and a hi-tech polymer designed to absorb shift shock and harmful vibrations.
- The small diameter design allows for more exhaust flow and higher horsepower.
- Adapts to the OEM thrust washer and prop nut.
- Included accessories and parts: Hub assembly, prop nut spacer, installation instructions.
- Installation Kits for Colman®, Evinrude®, Honda®, Johnson®, Mariner®, Mercury®, Nissan®, Parsun®, Suzuki®, Tohatsu®, & Yamaha® Outboards.
- Use with Hustler propeller housings for 6-20hp engines with 2.5" gearcase.
- See application chart for engine application information.
Turning Point is the only company to offer MasterGuard® Installation kits and prop housings for 6-300+hp engines with a Lifetime Warranty Hub. Boaters save up to 33% when buying a replacement propeller housing. MasterGuard hubs are Re-useable most of the time after a prop strike, and if not, they are Warrantied even if the prop is Destroyed (hub warranty on consumer use only - visit https://tpprops.com/warranty for details) . These hubs offer enhancedlower unit protection.
Turning Point's MasterGuard Hubs are engineered to withstand typical wear and tear over time without risk of spinning or failure under normal operational use. Turning Point's unique patented one piece hub with glass filled nylon over durable marine bronze splines eliminates failures commonly seen in multi-part "sleeve and spline" designs, and pressed-in rubber hub systems.
Eliminate Hub System Vibration and Chatter: Innovative one piece design reduces the number of parts and eliminates failures commonly seen in multi-part hub systems.
Eliminate Hub Cracking and Failure: The glass reinforced high-tech polymer construction increases flexibility, eliminating potential material stress fractures.
Corrosion Resistant Materials: Premium corrosion resistant durable marine bronze splines.
Reduce Gear Shock and Engine/Drive Damage: MasterGuard hubs offer Shock absorbing high-tech polymer cushion with lower unit protection.
Easy to Install: Clear and easy step-by-step directions coupled with minimal parts makes installation easy.
ALT Part Numbers: TUR 11100101, 23-6389, 26-6712
Important Note for Boat, Engine and Generator Parts: The responsibility for the accuracy of your order rests with you, the customer. If you have any question as to whether or not the part you are ordering is the right one for your boat/engine/generator, please do not hesitate to call us immediately at 321-952-1303 Monday-Friday 8-5pm. This is important to save both time and money. Carp Coastal Marine will be responsible for any mistakes that we make. However, if you make the decision without consult from us, then restocking and freight charges will be added to your order.
Brand: Turning Point Propellers
SKU:708-11100101
UPC:652480200588